how to remove skateboard wheels without tool
Once you've removed all hardware from your skateboard deck, it's time to start peeling that old grip tape off. Bearing race removal: First you need a hammer, punch, gloves, safety glasses, a torch and a piece of scrap wood to go between the hub and whatever surface you're hammering the hub on. Be careful when removing bearings. Wheel nuts are usually ½â (13 mm), so use that size. Remove the nuts from your roller skate wheels using a wrench. Put the nut and washer aside. Now, take the skate tool or plier and put it around the bolt of the truck. It includes all tools necessary to disassemble a skateboard and can be easily carried to your skate spot in a backpack or the trunk of your car. This makes it a little bit easier. If the grip tape breaks, use the razor again and apply more heat as needed. Tips. It's usually challenging to install them. Start with your skateboard deck; make sure that it is on its side. If you feel your wheels hitting the bottom of your deck when you are turning, you may want to refer to the Wheel Bite Prevention guide. The first thing that you need to do is take the trucks off your skateboard. you can remove those bearings with a blunt tipped screwdriver or allen key. Repeat this for each of the remaining wheels. The wheel is attached to the axle, so this part has to point upward. The best way is to use a bearing press - a special tool designed for inserting and removing bearings from wheels. Place the wrench over the nut in the center of 1 of the wheels and turn it counterclockwise until the nut comes off. A skateboard, of course; A skate tool; To start taking off the truck, you will put the truck in horizontal position. Though it is not necessary, I just like it doing this way. If you don't have a skateboard tool, or it doesn't have a socket, use a crescent or socket wrench. If the bearing doesnât budge out, you can use a flat screwdriver to get out easily. After removing wheel from the hub you should be able to get the seals and bearings out with basic tools (Keep the seals for the time being). Lay your skateboard on its deck so that the wheels are now facing up. Once the wheels are free, remove the bearings using one of the following methods: 8mm axles â Pry out the first bearing using a bearing puller in the middle of the hub. Once your wheels are installed, you can ride your skateboard. You can ⦠Slowly rotate the wheel while leveraging the bearing to pull it out of the hub. Give the author +30 points! Use an ½ inch or 13mm socket wrench to remove the axle nuts and bolts from the wheels' outsides.Now that you've taken apart your wheels, ensure that you keep all the wheel materials safe. Use a socket wrench, ratchet wrench, or the wrench side of a multi-function skate tool. There's no need for you to pay for this type of service when you can do it for yourself in a few minutes. Take the nuts off of all four wheels at once if you are changing all of the bearings. First remove the axle nut and the wheel. Set aside the nut and the two small washers that are on either side of the wheel. Skaters typically use the exposed axle to do this, though there are tools that make this much easier. Without damaging the bearings, you''ll want to pry them out of the wheels. Consider investing in a skate tool. Use the socket on your skateboard tool to remove the nut on the end of the axle. Put a sharp tap on the case of your bearing to remove it. Some skate tools will have a small cylindrical protrusion for prying bearings out of wheels, but the end of the axle works well too. Pull up to remove. Step IV. The assembly sits in the inner parts of the skateboard wheels. Now pry your skateboard wheels out before you can remove the main bearing assembly. a few tricks for removing bearings from wheels without a dedicated remover: start by removing bearings that would be on the outside of the wheel, so that as you push the bearing out, it falls out of the wheel onto a table. Now, you're ready for fresh wheels and bearings. DIY Removing Grip Tape from Skateboarding. Using the skate tool or the wrench, loosen the axle nut and remove the washer or the speed ring.